High-Speed Flight

From Mach 0.3, Deneb Aero solves the aircraft with its compressible method: SU2, a compressible RANS solver, on your computer. The air’s density changes around the aircraft, shocks can stand on the wing, and from Mach 1 shock waves leave the aircraft. This page says when the method is used, how a run is set up, what it needs and what its result can be trusted for.

When it is used

The Mach number decides. It follows from the speed and the air you give in the Flight step (How it is solved).

Mach number

Method

Below 0.3

Low-speed (OpenFOAM).

0.3 to 0.5

Compressible. Up to 110 m/s you may choose Low-speed instead, for the polar through stall and the flight model, with the lift reading 5 to 13% low.

0.5 to 1

Compressible.

1 to 5

Compressible, with shocks. The results add the shock waves and the sonic boom.

Past Mach 5 no method takes the speed. A speed is also refused where the air brought to rest at the nose would pass 2,000 K: there air starts to dissociate, which the model of the air does not include.

A high-speed run is one flight state: one speed, one altitude and one angle of attack. It gives the coefficients, the forces and the flow. It gives no polar, no stability and no flight model. To solve several Mach numbers in one analysis, see Several Speeds.

Setting up a run

An analysis at Mach 0.3 or more has five steps: Upload, Geometry, Flight, Package and Review. It has no Mesh step: the run is meshed after you launch it.

  1. In the Flight step, type the Speed or the Mach number, the Altitude and the Temperature against standard, as in Step 3: Flight. The line under them gives the Mach number, the speed range and the time, for example Mach 2.00, supersonic. The mass is not asked.

  2. Type the Angle of attack, from −10° to 20°. The wind is tilted; the body stays level. The hint gives the stagnation temperature and the air the run uses.

  3. Under What is it?, choose what the body is. It sets the solver’s settings and what the result can be trusted for:

    Wing or aircraft

    A lifting wing, alone or on a fuselage.

    Finned body

    A slender body with fins: a missile or a rocket.

    Another shape

    Any other shape, solved with the settings of the nearest of the two.

  4. Select Choose a package. The Package step has one starting point, High speed. From Mach 1.2 you can also tick Meshed for the sonic boom: 30% of the points go to cells of one size below the aircraft, where the boom is read. The loads are a little less resolved, and the time is the same.

  5. Select Review. Check Solver ready, Mesh planned (the points and the memory) and Estimated turnaround, then select Launch.

The air

From a stagnation temperature of 400 K, about Mach 1.4 at sea level and Mach 2.1 at 11 km, the air is thermally perfect: its heat capacity rises as it heats. Below that, the air is calorically perfect, with γ 1.4. In both, the air does not react.

What it needs

Memory

A run needs about 11 GB of memory that Deneb Aero may use. It uses at most 13 GB, which gives about a million points; with less, the mesh has fewer points. Deneb Aero may use 75% of the memory on a Mac or on Linux, so 16 GB is enough there. On Windows it may use 85% of what WSL has, so WSL needs about 12 GB. With less, the Flight step says A compressible run needs 11 GB of memory; Deneb Aero may use … GB here, and the run cannot be launched. See System Requirements.

Disk

About 1 GB a run.

Time

Half an hour to an hour on an M3 Pro Mac. Before you launch, the Studio estimates the time for this computer. Once this computer has finished three runs at subsonic speeds, or three at supersonic ones, the Studio times from those.

High-speed and low-speed runs do not solve at the same time: each waits for the other.

How a run is solved

  1. The parts are united into one closed surface, which is remeshed.

  2. Pass 1 solves from the free stream on a coarser mesh and stops once its loads settle.

  3. Pass 2 refines the surface where pass 1 found shocks, meshes at the run’s full size and goes on from pass 1’s solution until it converges, for at most 5,000 iterations.

While it runs, the project shows the stage, the pass and SU2’s iterations. Select Stop to stop it. A high-speed run cannot be paused. More detail is in Method.

What it can be trusted for

Each run carries a label. The ? beside the line in the Flight step shows it before you launch, and the result’s Overview shows it under What it can be trusted for.

Validated

Inside a benchmark that passed. No compressible run has this label yet.

Verified numerics

A checked case covers the body and the Mach number. Its measured differences are shown beside the result.

Exploratory

No case like it has been checked against a measurement. The numbers are the solver’s.

A run is Verified numerics here, and Exploratory everywhere else and for Another shape:

Body

Mach

Checked against

Measured there

Wing or aircraft

0.7 to 0.9

The ONERA M6 wing, against NASA’s codes on the same grid.

Lift −0.3 to −2.1%, drag −0.3 to −4.0% and pitching moment −0.3 to −3.0% of NASA’s codes. Surface pressure where the flow is supersonic oscillates and is not trusted.

Finned body

1.29 to 2.5

The Basic Finner, against DREV’s aeroballistic range, on a fine grid.

CNα within 6.5% and Cmα within 5% of the range. CA 5 to 17% high, most at the lower Mach numbers: base suction.

Finned body

2.5 to 3.15

The Basic Finner, against DREV’s aeroballistic range, on a medium grid.

CNα within 1.3% and Cmα within 6.3% of the range. CA 3.5 to 5.2% high. The loads swing by 0.1 to 0.6% and do not meet the convergence rule; the swing is shown with them.

The results

A high-speed project opens on its own page:

  • Overview: lift, drag, pitching moment and L/D, the flow in 3D and what the result can be trusted for. From Mach 1.2, the nose’s shock against cone theory, where the check applies.

  • Flow on planes: Mach, Cp, schlieren, knife edge or temperature, on planes across the flow, along the span or from above.

  • Surface: Cp, temperature, wall shear or y⁺ on the walls, with the sonic surface.

  • Loads: each coefficient with its pressure and friction parts, each part’s share, and how far the run converged.

  • Sonic boom, above Mach 1.05: the boom carried down to the ground, its loudness as Perceived Level, and its signature to play.

  • Report: the report of the run. Print it or save it as PDF.

In an analysis over several speeds, each compressible speed opens the same page.

Good to know

  • The compressible method is fully turbulent: it has no laminar flow, so a laminar wing’s drag reads high.

  • If Deneb Aero quits or is updated during a run, the run stops and does not resume. The project shows The run did not finish. Start the analysis again.